Добавил:
Andrey
Опубликованный материал нарушает ваши авторские права? Сообщите нам.
Вуз:
Предмет:
Файл:ARM PrimeCell multiport memory controller technical reference manual.pdf
X
- •Contents
- •List of Tables
- •List of Figures
- •Preface
- •About this document
- •Feedback
- •Introduction
- •1.1 About the ARM PrimeCell MultiPort Memory Controller (PL172)
- •1.2 Supported dynamic memory devices
- •1.3 Supported static memory devices
- •Functional Overview
- •2.1 PrimeCell MPMC functional description
- •2.2 Overview of a PrimeCell MPMC, ASIC, or ASSP system
- •2.3 Low power operation
- •2.4 Lock and semaphores
- •2.5 Arbitration
- •2.6 Memory bank select
- •2.7 Memory map
- •Programmer’s Model
- •3.1 About the programmer’s model
- •3.2 Register descriptions
- •Programmer’s Model for Test
- •4.1 PrimeCell MPMC test harness overview
- •4.2 Scan testing
- •4.3 Test registers
- •Static Memory Controller
- •5.1 Static memory device selection
- •5.2 Write-protection
- •5.3 Extended wait transfers
- •5.4 Memory mapped peripherals
- •5.5 Static memory initialization
- •5.6 Byte lane control
- •5.7 Byte lane control and databus steering for little and big-endian configurations
- •Dynamic Memory Controller
- •6.1 Write-protection
- •6.2 Access sequencing and memory width
- •6.3 Address mapping
- •6.4 Dynamic memory controller command descriptions
- •6.5 Generic SDRAM initialization example
- •6.6 Micron MT48LC4M16A2 SDRAM initialization example
- •6.8 Micron MT28F4M16S2 SyncFlash initialization example
- •6.9 Micron SyncFlash commands
- •Common Memory Transactions
- •7.1 Static and dynamic memory transaction latency
- •Test Interface Controller
- •8.1 About TIC
- •8.2 Sequence of events leading to entry into TIC test mode
- •System Connectivity
- •9.2 Self-refresh entry
- •9.3 Example system
- •Off-chip Connectivity
- •10.2 Pin count reduction by reducing databus width
- •10.3 Pin count reduction by removing functionality
- •10.4 Address pin reduction
- •10.5 Chip select pin reduction
- •10.6 Device support
- •10.7 Multiplexing static and dynamic memory pins
- •10.8 Reducing pin count by multiplexing MPMC pins
- •10.9 About MPMC timing
- •10.10 On-chip timing path
- •10.11 Off-chip timing path
- •10.12 Clock strategy
- •10.13 Clock ratios
- •10.14 Memory clock and fed-back clock strategy
- •Pad Interface Timing
- •A.1 Overview
- •A.2 Signal delay
- •A.3 Method to reduce delay
- •A.4 Methods to reduce skew
- •A.5 Methods to minimize the effects of delay and skew
- •A.6 Example SDRAM memory timing diagram
- •A.7 SDRAM memory timing paths
- •Troubleshooting
- •B.1 Troubleshooting
- •C.1 AHB register signals
- •C.2 AHB memory signals
- •C.3 Miscellaneous and clock signals
- •C.4 Pad interface and control signals
- •C.5 Test Interface Controller (TIC) signals
- •C.6 Scan test signals
Preface
Feedback
ARM Limited welcomes feedback both on the ARM PrimeCell MultiPort Memory
Controller (PL172), and on the documentation.
Feedback on the ARM PrimeCell MultiPort Memory Controller (PL172)
If you have any comments or suggestions about this product, please contact your supplier giving:
•the product name
•a concise explanation of your comments.
Feedback on this document
If you have any comments on about this document, please send email to errata@arm.com giving:
•the document title
•the document number
•the page number(s) to which your comments refer
•a concise explanation of your comments.
General suggestions for additions and improvements are also welcome.
xviii |
Copyright © 2002 ARM Limited. All rights reserved. |
ARM DDI 0215A |
Соседние файлы в предмете Электротехника